Send Message

TOBO STEEL GROUP CHINA

Home News

ASTM 35 1 Gr. CF8M 316 SS 6000# valve

Company News
ASTM 35 1 Gr. CF8M 316 SS 6000# valve

Needle Valve Female Thread 1/4" Stainless Steel SS316 Flow Control Shut Off Crane Adjustable Needle Valve

 

Needle valves:

 

A needle valve is a type of valve with a small port and a threaded, needle-shaped plunger. It allows precise regulation of flow, although it is generally only capable of relatively low flow rates.

  • Investment Cast
  • Body – ASTM 351 Gr. CF8M
  • Packing – Teflon
  • Stem – 316 SS
  • Handle – 304 SS
  • Maximum pressure psi6000

Needle Valve Work:

 

Needle valves open and close an orifice with a tapered end that raises and lowers with the spin of a handle. Figure 2 shows a needle valve cross sectional view, design, and components. The handle (A) is connected to the plunger, also called a stem (F). When you turn the handle, the plunger moves up or down based on the threads (C). The locking nut (B) prevents it from fully unscrewing. As the plunger moves down, the tapered pointed end (I) comes into contact with the valve seat to fully seal the orifice (H). Often, the valve seat is also tapered. There are various options and sizes available to connect it to a pipe or hose through the port connection (G) on the input and output. The bonnet (D) is connected to the valve housing (E), which can be made out of different materials like brass or stainless steel.

latest company news about ASTM 35 1 Gr. CF8M 316 SS 6000# valve  0

Based on the threads, you can very precisely locate the plunger’s tapered end away from the valve seat to accurately control the flow rate. Therefore, by varying the plunger location you will control the flow rate between maximum and zero.

Different types of needle valves:

A manually operated threaded needle valve (described above) is the most common type of needle valve. However, two additional variants are: motorized and angle.

  • Motorized Needle Valve: These needle valves don’t have a handle for manual operation, but instead use an electric or pneumatic actuator to connect to and turn the plunger. These can be remotely controlled, used in a closed loop system, and/or put on a timer to accurately control the flow rate remotely.
  • Angle Needle Valve: These needle valves turn the output from the inlet by 90 degrees instead of in-line. The same operation concept applies, but the 90-degree angle can allow for better system integration. Figure 3 shows an example of an angle needle valve.

latest company news about ASTM 35 1 Gr. CF8M 316 SS 6000# valve  1

Needle valve selection:

 

When selecting a needle valve, four main characteristics and/or application requirements need to be taken into account: material, pressure, size, and temperature.

Material

The needle valve's housing material (Figure 2 callout E) is specified according to the application. The most common valve housing materials are brass and stainless steel due to their range of chemical resistance, however, there are also other materials available for special applications.

Brass

Brass needle valves are suitable for hydraulic systems, drinking water, high temperature applications, and gas piping. They are suitable for neutral and non-corrosive media, with the most common implementation being for drinking water applications. However, they should not be used for salt water (seawater), distilled water, acids, or chlorides.

Stainless steel

Stainless steel needle valves have very good overall chemical resistance to almost any media. The material is very durable and can withstand high temperature and pressures. It is suitable for aggressive and corrosive media like seawater.

Pressure

Understanding the application requirements for pressure in your system is important for selecting the correct needle valve. Robust needle valves can handle pressure of up to 4,000 to 5,000 psi (275 up to 413 bar) at 100°F (38°C). When higher pressures are required, like for high pressure hydraulic applications, high performance valves are available that can handle up to 10000 psi (689 bar) pressure at 100°F (38°C). Special designs are also available when you need a vacuum needle valve to handle the low pressure.

Port & orifice size

Needle valves are available in a wide range port and orifice sizes. The connection ports can also be male or female ends. Common thread standards used are NPT (National American Pipe Thread), BSP (British Standard Pipe), or metric (ISO standards). The most commonly used needle valves range from 2 to 12 mm or 1/8” to 2”. Ensuring the correct port size and orifice size will ensure efficient flow and system operation with less chances of wear and/or leakage.

Temperature

Needle valves are suitable for high or low temperature applications. You need to specify the valve housing and packing/sealing material appropriately, especially for extreme temperatures, to ensure it can withstand the requirements. The two most common sealing materials are PTFE (Teflon) for a temperature range of -65°F to 450°F (-54° C to 232°C) and PEEK (Polyether Ether Ketone) for increased temperature resistance up to 600°F (315 °C).

Needle valve applications

You will see needle valves across all fluid control applications due to their ability to precisely control flow rates. By selecting the appropriate valve material and size for temperature and pressure, they can be used for almost any clean gas or fluid. One of the most commonly used location for needle valves is to monitor gas flow, like propane, in a system. A propane needle valve can accurately shut it off and/or control the flow rate and effectively the burn rate for applications.

Needle valve symbol

If looking at a schematic, Figure 4 shows a needle valve symbol. It has the standard 2-way valve symbol with an arrow indicating it is a needle valve.

latest company news about ASTM 35 1 Gr. CF8M 316 SS 6000# valve  2

Pub Time : 2021-08-21 00:40:42 >> News list
Contact Details
TOBO STEEL GROUP CHINA

Contact Person: Ms. TOBO

Tel: 021-31262012

Send your inquiry directly to us