amy@tobo-group.com
ASME B16.1 CL 125 GATE VALVE BS5163 CAST IRON PN16 RISING STEM SOFT SEAL STEEL GATE VALVE
Quick Details
Technical Requirement:
1. Design and Manufacture: DIN 3352;
2. Face to Face: DIN 3202 F4/F5;
3. Flange End: DIN 2532 PN10/16;
Specification:
Part No. | Part | Standard Specification | Options |
1 | Valve Body | ASTM A536, 65-45-12 | |
2 | Resilient Wedge Disc | ASTM A536, 65-45-12+SPDM | AISI 304, AISI 316, AISI 420,AISI 431 |
3 | Stem | Stainless Steel | AISI 304, AISI 316, AISI 416 |
4 | Bonnet Gasket | EPDM | NBR |
5 | Bonnet | ASTM A536, 65-45-12 | |
6 | Washer | Brass Hpb59-1 | |
7 | Yoke | ASTM A536, 65-45-12 | |
8 | Stem Bushing | Brass Hpb59-1 | |
9 | Gland | ASTM A536, 65-45-12 | |
10 | Stem Nut | Brass Hpb59-1 | Bronze ZQSn5-5-5 |
11 | Handwheel | ASTM A536, 65-45-12 | Pressed Steel |
12 | Washer | Brass Hpb59-1 | |
13 | Gland Nut | Carbon Steel Zinc Plated | AISI 304, AISI 316 |
14 | Stud | Carbon Steel Zinc Plated | AISI 304, AISI 316 |
15 | Flat Washer | Carbon Steel Zinc Plated | AISI 304, AISI 316 |
16 | Nut | Carbon Steel Zinc Plated | AISI 304, AISI 316 |
17 | O-Ring | NBR | EPDM |
What is Gate Valve?
A gate valve can be defined as a type of valve that used a gate or wedge type disk and the disk moves perpendicular to flow to start or stop the fluid flow in piping.
A gate valve is the most common type of valve used in any process plant. It is a linear motion valve used to start or stop fluid flow. In service, these valves are either in a fully open or fully closed position.
When the gate valve is fully open, the disk of a gate valve is completely removed from the flow. Therefore virtually no resistance to flow. Due to this very little pressure drops when fluid passes through a gate valve.
To achieve proper sealing, when the valve is fully closed, 360° surface contact is required between disk and seats.
Gate valves should not be used for regulation or throttling of flow because accurate control is not possible.
The high velocity of the flow in the partially open valve may cause erosion of the disc and seating surfaces and also creates vibration and noise.
Valve Type | CS / SS GATE VALVE - FL / BW | |
Design Std | BS EN ISO 10434 [BS 1414] / API 600 / API 602 / API 603/ASME B16.34 | |
Size Range | 40 DN to 400 DN [1 1/2” to 16”] | |
Body | [CS - ASTM A 216 Gr. WCB] [SS - ASTM A 351 Gr.CF8 / CF8M] | |
Trim | AISI 410 / 304 / 316 | |
Seat / Wedge | 13% Cr. Steel / AISI 410 / 304 / 316 | |
Design Features | Bolted Bonnet, OS & YT, HW & Gear operated | |
Prorating | ASME - Class 150 / 300 / 600 | |
Face to Face | ASME B 16.10 / EN 558 -1 / API 6D | |
End Connection | Flanged | ASME B16.5, CLASS 150 / 300 / 600 |
Butt weld | ASME B16.25 | |
Testing Std. | BS EN 12266 - 1 [BS 6755-1] / API 598 | |
Optional | Lantern Ring / indicator & Locking Device/ Renewable Seat / Stellite Hard facing / Jacketed Provision / RTJ Flanges / By Pass Arrangement / Higher Sizes / Special MOC: Austenitic and Duplex Stainless Steels |
PN | DN | Size(mm) | ||||||
L | D | D1 | D2 | B | N-φ | H | ||
1.6MPa | 25 | 160 | 115 | 85 | 65 | 14 | 4-14 | 275 |
32 | 180 | 135 | 100 | 78 | 16 | 4-18 | 280 | |
40 | 200 | 145 | 110 | 85 | 16 | 4-18 | 330 | |
50 | 230 | 160 | 125 | 100 | 16 | 4-18 | 350 | |
65 | 290 | 180 | 145 | 120 | 18 | 4-18 | 370 | |
80 | 310 | 195 | 160 | 135 | 20 | 8-18 | 400 | |
100 | 350 | 215 | 180 | 155 | 20 | 8-18 | 415 | |
125 | 400 | 245 | 210 | 185 | 22 | 8-18 | 460 | |
150 | 480 | 280 | 240 | 210 | 24 | 8-23 | 510 | |
200 | 550 | 335 | 295 | 265 | 26 | 12-23 | 710 | |
250 | 650 | 405 | 355 | 320 | 30 | 12-25 | 786 | |
300 | 750 | 460 | 410 | 375 | 30 | 12-25 | 925 |
Types of Gate Valves
There are three ways to classify the gate valve.
Types of Disk
Solid taper wedge
Flexible wedge
Split wedge or Parallel disks Valve
Types of Body Bonnet Joint
Screwed Bonnet
Bolted-Bonnet
Welded-Bonnet
Pressure-Seal Bonnet
Types of Stem movement
Rising Stem or OS & Y Type (Outside Stem and Screw Type)
Non-rising Stem type
Contact Person: Ms. TOBO
Tel: 021-31262012
Water Oil Base Gas Cast Steel SS 3 Way Ball Valve Flanged End Full Port Ball Valve
Stainless Steel Floating Ball Valve Three Way Simple Structure Easy Operation
4 Way Ball Valve SS316 Body / Ball / Stem PTFE seats Flange ANSI Class 150 Ball Valve
CF8 1.6MPa 2 Inch Stainless Steel Gate Valve , Class 150 Flange End Manual Gate Valve
SS304 DN100 PN16 Stainless Steel Gate Valve Powder Coated
ASTM A126 1" 175 PSI Rising Plug Valve 10000 PSI H Series Flanged Plug Valve
SS304 3/4'' 150LB Manual Globe Valve , Flanged Globe Valve Stainless Steel
1/2'' 150LB Manual Stainless Steel Globe Valve Flange End SS304 A351 CF8 Globe Valve
High Temperature WCB Globe Valve , 3/4'' 150LB Flange End Carbon Steel Globe Valve