DN65 PN16 Cast Iron Flanged Gate Valve High Temperature Steam
What is Gate Valve?
A gate valve can be defined as a type of valve that used a gate or wedge type disk and the disk moves perpendicular to flow to start or stop the fluid flow in piping.
A gate valve is the most common type of valve used in any process plant. It is a linear motion valve used to start or stop fluid flow. In service, these valves are either in a fully open or fully closed position.
When the gate valve is fully open, the disk of a gate valve is completely removed from the flow. Therefore virtually no resistance to flow. Due to this very little pressure drops when fluid passes through a gate valve.
To achieve proper sealing, when the valve is fully closed, 360° surface contact is required between disk and seats.
Gate valves should not be used for regulation or throttling of flow because accurate control is not possible.
The high velocity of the flow in the partially open valve may cause erosion of the disc and seating surfaces and also creates vibration and noise.
|Valve Type||CS / SS GATE VALVE - FL / BW|
|Design Std||BS EN ISO 10434 [BS 1414] / API 600 / API 602 / API 603/ASME B16.34|
|Size Range||40 DN to 400 DN [1 1/2” to 16”]|
|Body||[CS - ASTM A 216 Gr. WCB] [SS - ASTM A 351 Gr.CF8 / CF8M]|
|Trim||AISI 410 / 304 / 316|
|Seat / Wedge||13% Cr. Steel / AISI 410 / 304 / 316|
|Design Features||Bolted Bonnet, OS & YT, HW & Gear operated|
|Prorating||ASME - Class 150 / 300 / 600|
|Face to Face||ASME B 16.10 / EN 558 -1 / API 6D|
|End Connection||Flanged||ASME B16.5, CLASS 150 / 300 / 600|
|Butt weld||ASME B16.25|
|Testing Std.||BS EN 12266 - 1 [BS 6755-1] / API 598|
|Optional||Lantern Ring / indicator & Locking Device/ Renewable Seat / Stellite Hard facing / Jacketed Provision / RTJ Flanges / By Pass Arrangement / Higher Sizes / Special MOC: Austenitic and Duplex Stainless Steels|
Types of Gate Valves
There are three ways to classify the gate valve.
Types of Disk
Solid taper wedge
Split wedge or Parallel disks Valve
Types of Body Bonnet Joint
Types of Stem movement
Rising Stem or OS & Y Type (Outside Stem and Screw Type)
Non-rising Stem type
● Flat-bottomed seat traditional gate valves are usually deposited in the bottom groove of the valve due to external objects
such as stone, wood, cement, paper, debris, etc., after flushing the pipe with water. Cause cannot close tightly and form slack
phenomenon, soft-sealing gate valve using the same as the pipe at the bottom of the flat design, not easy to cause debris deposition,
the fluid flow unimpeded, the whole package glue valve plate is made of high quality rubber, within the whole outsourcing, domestic
first-class rubber vulcanization technology make the valve plate after vulcanization can ensure accurate geometry size, and rubber
and nodular cast iron gate connecting firm, not easy to fall off and elastic memory preferred.
● The corrosion resistant valve body is painted with powder and epoxy resin to prevent corrosion and rust of the valve body, and can
be used in sewage system.
● Not easily broken into traditional cast iron.
Contact Person: Ms. TOBO
Water Oil Base Gas Cast Steel SS 3 Way Ball Valve Flanged End Full Port Ball Valve
Stainless Steel Floating Ball Valve Three Way Simple Structure Easy Operation
4 Way Ball Valve SS316 Body / Ball / Stem PTFE seats Flange ANSI Class 150 Ball Valve
CF8 1.6MPa 2 Inch Stainless Steel Gate Valve , Class 150 Flange End Manual Gate Valve
SS304 DN100 PN16 Stainless Steel Gate Valve Powder Coated
ASTM A126 1" 175 PSI Rising Plug Valve 10000 PSI H Series Flanged Plug Valve
SS304 3/4'' 150LB Manual Globe Valve , Flanged Globe Valve Stainless Steel
1/2'' 150LB Manual Stainless Steel Globe Valve Flange End SS304 A351 CF8 Globe Valve
High Temperature WCB Globe Valve , 3/4'' 150LB Flange End Carbon Steel Globe Valve